Emerson DLC3020f Manuál s instrukcemi Strana 28
- Strana / 200
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Instruction Manual
D103434X012
Configuration
November 2014
26
Figure 4‐2. Guided Setup
GUIDED SETUP
INSTRUMENT SETUP
CONFIGURE
Manual Setup
AMS Device Manager Configure > Manual Setup
Field Communicator Configure > Manual Setup
The Device, Process Fluid, Instrument Display, Snap Acting Control, and Options tabs are accessible through Manual Setup.
Note
An error will be generated if the instrument is put back in service without applying device configuration changes; you must apply
changes before putting the instrument back In Service. To clear an error, set the Mode to Out of Service, select Apply, then put
back In Service.
- FIELDVUE 1
- DLC3020f Digital Level 1
- Controller for F 1
- fieldbus 1
- Contents 3
- Scope of Manual 5
- Instrument Description 5
- Foundation Fieldbus Blocks 5
- Using This Manual 6
- Specifications 7
- Related Information 7
- Educational Services 7
- Instruction Manual 10
- 28B5536‐1 11
- Section 2 Installation2‐2‐ 13
- Lever Lock 14
- Mounting 15
- DLC3020f Orientation 16
- 20A7423‐C 18
- DIGITAL LEVEL CONTROLLER 18
- AMBIENT TEMPERATURE (_C) 19
- STANDARD TRANSMITTER 19
- 39A4070‐B 19
- Fieldbus Connections 20
- Simulate Enable Jumper 21
- GE46500‐B 22
- Section 3 Overview3‐3‐ 23
- Primary Purpose Variables 24
- Shortcuts 24
- Section 4 Configuration4‐4‐ 27
- Manual Setup 28
- Variable Configuration 29
- Sensor Limits 29
- Sensor Hardware Information 30
- Sensor Units 30
- Sensor Parameters 31
- Torque Tube 32
- Process Fluid 33
- Temperature Compensation 33
- View Fluid Density Table 34
- Display Option 34
- Decimal Places 34
- Display Primary Value Offset 35
- Scrolling Message Control 35
- Snap Acting Control 35
- Primary Value 35
- Primary Value Percent 36
- DI1 Trip Point Settings 36
- DI2 Trip Point Settings 36
- Write Alarm 37
- Block Alarm 37
- Write Lock 37
- Confirm Time 38
- Communication Timeout 38
- Function Block Available 38
- Transducer Block 39
- Features Selected 39
- Alert Key 39
- Maximum Alerts Allowed 39
- Alert Setup 40
- PlantWeb Alerts 41
- Electronics 41
- Operational 41
- Rate Limit 41
- Calibration in Use 43
- Calibrate Instrument 44
- Full Calibration 45
- Trim Current Calibration 46
- Alert Conditions 47
- Variables 48
- Run Time Extremes 49
- Simulate 50
- Calibration Setup/Logs 51
- Instrument Display Test 52
- Restart Device 52
- Tools Required 53
- LCD Meter Assembly 55
- Removing the LCD Meter 56
- Replacing the LCD Meter 56
- Electronics Module 57
- Terminal Box 58
- Assembly 59
- Lever Assembly 60
- Packing for Shipment 61
- Instrument Troubleshooting 62
- Section 8 Parts8‐8‐ 65
- Parts Kits 66
- Parts List 66
- Transducer Assembly 68
- (figure 8‐2) 68
- Terminal Box Assembly 69
- (figure 8‐3) 69
- Terminal Box Cover Assembly 69
- (figure 8‐4) 69
- 28B5741‐B 70
- 29B8444‐A 71
- 29B8445 B 71
- Yamatake NQP Sensor 72
- Foxboro‐Eckardt Sensors 72
- 249 SENSOR (SIDE VIEW) 73
- FIELDBUS‐FBUS_31A 75
- FIELDBUS‐FBUS_03A 77
- Signal Conversion 78
- Advanced Features 79
- AI Block Parameter List 81
- TRANSDUCER_STATUS 9.3 RO 0 82
- UNACKNOWLEDGED 22.2 RO ALL 83
- PID Function Block 87
- Filtering 90
- Feedforward Calculation 91
- Output Tracking 91
- Set Point Tracking 91
- Reverse and Direct Action 92
- PID Block Parameter List 94
- 3=Active reported 97
- 4=Active not reported 97
- Unacknowledged 100
- T_AUTO_HYSTERESIS 101
- View Lists 102
- Status Handling 107
- I/O Selection 107
- Block Initialization 107
- Field Value Processing 108
- Alarm Detection 108
- Block Errors 109
- Action on Failure 109
- Simulation 109
- Mode Handling 116
- Shed With Return Options 117
- Shed With No Return Options 117
- Setting the Output 118
- Action On Fault Detection 119
- I/O Options 120
- Application Information 121
- CAP_STDDEV 125
- Limit Propagation 130
- Substatus Propagation 130
- STATUS_OPTS Supported 130
- SELECT_TYPE Must 132
- Input Selection 133
- Supported Modes 143
- Block Execution 144
- Advanced Topics 146
- Troubleshooting 148
- Resource Block 152
- AUTO 0 to 65535 0 159
- AUTO 1 to 255 1 159
- AUTO 3:AUTO 159
- AUTO 0 to 15 2 168
- Transducer Block (LCD) 174
- Function Block Overview 181
- Resource Blocks 182
- Transducer Blocks 182
- Block Modes 183
- Explanation of Modes 184
- Device Descriptions 185
- Status Propagation 186
- Network Communication 187
- Scheduled Transfers 188
- Unscheduled Transfers 189
- Network Management 190
- Glossary 191
- D103434X012 192
- November 2014 192
Související produkty a manuály pro Měření, testování a kontrola Emerson DLC3020f
(3 stránky)
Měření, testování a kontrola Emerson 3051S Specifikace
(188 stránky)
(188 stránky)
Měření, testování a kontrola Emerson 3051S Specifikace
(240 stránky)
(240 stránky)
Měření, testování a kontrola Emerson 3051S Specifikace
(240 stránky)
(240 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce