Emerson D3 Manuál s instrukcemi

www.Fisher.comFisherr D3 FloPro Control ValveContentsIntroduction 1...Scope of Manual 1...Desc

Instruction ManualD103221X012D3 FloPro ValveFebruary 2014109. LubricatethebonnetO-ring(key4)withlithiumgreaseandinstallonthebonnet.10. Apply anti-seiz

Instruction ManualD103221X012D3 FloPro ValveFebruary 2014112. Use the lower packing spacer (key 12) and a tube to push the upper anti-extrusion washer

Instruction ManualD103221X012D3 FloPro ValveFebruary 2014124. Apply a 3mm (1/8 inch) bead of the supplied high performance fluorinated grease (key 44)

Instruction ManualD103221X012D3 FloPro ValveFebruary 2014132. Remove the ten short actuator casing cap screws (key 29).3. Remove the two long actuator

Instruction ManualD103221X012D3 FloPro ValveFebruary 201414Inspect all parts for wear or damage during disassembly. Replace any worn or damaged parts

Instruction ManualD103221X012D3 FloPro ValveFebruary 201415Figure 6. Spring Locations As Seen From Above Lower Actuator Casing6SPRINGS3 SPRINGS 2 SPRI

Instruction ManualD103221X012D3 FloPro ValveFebruary 2014162. Lubricate the stem O-ring (key 25) with lithium grease and install in the bonnet (key 7)

Instruction ManualD103221X012D3 FloPro ValveFebruary 201417CAUTIONAvoid possible product damage which may affect proper operation of the diaphragm. En

Instruction ManualD103221X012D3 FloPro ValveFebruary 201418Make sure all parts are clean and in good condition before starting assembly. There should

Instruction ManualD103221X012D3 FloPro ValveFebruary 20141913. Install the male packing adaptor, lower anti-extrusion washer (key 10), and lower packi

Instruction ManualD103221X012D3 FloPro ValveFebruary 20142Table 1. SpecificationsValve Body Sizes and End Connection Styles(1)See table 3Maximum Inlet

Instruction ManualD103221X012D3 FloPro ValveFebruary 20142029. Install the two long cap screws (key 31) opposite each other. Install the ten short cap

Instruction ManualD103221X012D3 FloPro ValveFebruary 201421Figure 7. Fisher D3 FloPro Valve Assembly (Spring-to-Close)GE21319-BVIEW ABELLEVILLE SPRING

Instruction ManualD103221X012D3 FloPro ValveFebruary 201422Figure 8. Fisher D3 FloPro Valve Assembly (Spring-to-Open)GE21338-BVIEW ABELLEVILLE SPRINGA

Instruction ManualD103221X012D3 FloPro ValveFebruary 201423Parts KitsTRIMKITSPort Diameter (inches) 0.375 0.75 1Standard trim kit (Contains keys 2, 3,

Instruction ManualD103221X012D3 FloPro ValveFebruary 201424Emerson Process ManagementMarshalltown, Iowa 50158 USASorocaba, 18087 BrazilChatham, Kent M

Instruction ManualD103221X012D3 FloPro ValveFebruary 20143Table 3. Valve Sizes and Connection StylesVALVESIZE,NPSPORT DIAMETER, (INCHES)THREADED RAISE

Instruction ManualD103221X012D3 FloPro ValveFebruary 201443. The control valve assembly may be installed in any orientation, but normally the actuator

Instruction ManualD103221X012D3 FloPro ValveFebruary 201453. Retighten the socket head screws (key 15) to 3 NSm(26lbfSin).MaintenanceRefer to figures

Instruction ManualD103221X012D3 FloPro ValveFebruary 201464. Tighten the hex socket head cap screws to 3 NSm(26lbfSin).5. Relieve pressure to the actu

Instruction ManualD103221X012D3 FloPro ValveFebruary 201473. Loosen the hex socket head cap screws (key 15) and raise the flow adjustor (keys 13 and 1

Instruction ManualD103221X012D3 FloPro ValveFebruary 20148Figure 3. Packing and Belleville Spring Stacking OrderUPPER PACKINGSPACER (KEY 12)ANTI-EXTRU

Instruction ManualD103221X012D3 FloPro ValveFebruary 20149Figure 5. Lubrication Locations on PackingFEMALE PACKING ADAPTERMALE PACKING ADAPTERPACKING