Emerson Liebert MicroPOD Maintenance Bypass and Output Distribution Accessory Uživatelská příručka

Procházejte online nebo si stáhněte Uživatelská příručka pro Nepřerušitelné zdroje napájení (UPS) Emerson Liebert MicroPOD Maintenance Bypass and Output Distribution Accessory. Emerson Liebert MicroPOD Maintenance Bypass and Output Distribution Accessory User Guide Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 22
  • Tabulka s obsahem
  • ŘEŠENÍ PROBLÉMŮ
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
POWER AVAILABILITY
2U Hardwire POD™
USER MANUAL
Power Output
Distribution
120 Volt
Zobrazit stránku 0
1 2 3 4 5 6 ... 21 22

Shrnutí obsahu

Strany 1 - 2U Hardwire POD™

POWER AVAILABILITY2U Hardwire POD™USER MANUALPower OutputDistribution120 Volt

Strany 2

6INSTALLATION ON GXT 2U UPS1. Unpack the 2U POD carefully, noting the packing method. Retain the box and packing material for possible future shipment

Strany 3 - TABLE OF CONTENTS

7HARDWIRE CONNECTIONSElectrical Installation Considerations The front and bottom of the POD provide alternate conduit entry points for both the UTILIT

Strany 4

8Wiring access doors on each end of the POD allow access to the wiring compartments by opening the top and rear of the POD. Each access door is retain

Strany 5 - SAVE THESE INSTRUCTIONS

9Wiring Instructions1. Remove the wiring access doors by removing the two Phillips head screws that secure them.2. Determine which of the two availabl

Strany 6

10APPLY FEED POWER1. Next attach the POD to the securing brackets (see Figure 7). The POD can be installed to face one of three different directions u

Strany 7 - GLOSSARY OF SYMBOLS

11START EQUIPMENT1. Turn on all loads hardwired to the output of the POD. The 2U POD now powers your equipment in the UTILITY mode.2. Turn ON the load

Strany 8 - System Description

12INDICATOR LAMPSUtilityThis amber lamp is illuminated when utility power is present. It sig-nals that you may transfer the loads to maintenance bypas

Strany 9 - RACK MOUNT INSTALLATION

13OPERATIONTransfer to Maintenance BypassTo transfer to maintenance bypass (UTILITY) from UPS, follow the following steps:1. Ensure the Utility lamp (

Strany 10 - INSTALLATION ON GXT 2U UPS

14TROUBLESHOOTINGProblem Cause SolutionUTILITY lamp (amber) not illuminated.UTILITY not present.Call qualified service personnel to restore power.Util

Strany 11 - HARDWIRE CONNECTIONS

15SPECIFICATIONSThis POD is intended for use with a UPS meeting all of the following requirements:• UPS input cord is compatible with the rating and t

Strany 15 - START EQUIPMENT

Technical Support/ServiceWeb Sitewww.liebert.comMonitoring800-222-5877monitoring@liebert.comOutside the US: 614-841-6755Single-Phase UPS800-222-5877up

Strany 16 - INDICATOR LAMPS

iTABLE OF CONTENTSIMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . 1GLOSSARY OF SYMBOLS . . . . . . . . . . . . . . . . . . . .

Strany 17 - OPERATION

FIGURESFigure 1 UPS mode of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Figure 2 Utility/maintenance bypass mode . . . . . .

Strany 18 - TROUBLESHOOTING

1IMPORTANT SAFETY INSTRUCTIONSSAVE THESE INSTRUCTIONSThis manual contains important instructions that should be followed during installation and opera

Strany 19 - SPECIFICATIONS

2!CAUTIONThis device receives power from multiple sources. Before servicing this device, remove all connections and cut power from the utility branch

Strany 20

3GLOSSARY OF SYMBOLSEquipment grounding conductorBonded to groundElectric phaseIndicates AC inputIndicates AC output

Strany 21

4INTRODUCTION AND SYSTEM DESCRIPTIONCongratulations on your choice of the Liebert 2U Hardwire POD™. The 2U Hardwire POD provides maintenance bypass ca

Strany 22

5RACK MOUNT INSTALLATION1. Rack mount installation of the 2U POD is possible with the use of the rack mounting brackets (shipped with the POD). See Fi

Komentáře k této Příručce

Žádné komentáře