Emerson 3051S Specifikace Strana 73
- Strana / 222
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
63
Reference Manual
00809-0100-4001, Rev JA
Section 3: Configuration
November 2012
Configuration
Field communicator
To initiate a loop test, perform the following procedure:
1. a. For 4-20 mA HART output, connect a reference meter to the transmitter by either
connecting the meter to the test terminals on the terminal block, or shunting
transmitter power through the meter at some point in the loop.
b. For 1-5 Vdc Low Power HART output, connect a reference meter to the V
out
terminal.
2. From the HOME screen, enter the fast key sequence “Loop Test” to verify the output of
the transmitter.
3. Select OK after the control loop is set to manual (see “Setting the loop to manual” on
page 40).
4. Select a discrete milliamp level for the transmitter to output. At the CHOOSE ANALOG
OUTPUT prompt select 1: 4mA (1 Vdc), select 2: 20mA (5 Vdc), or select 3: “Other” to
manually input a value.
a. If you are performing a loop test to verify the output of a transmitter, enter a value
between 4 and 20 mA (1 and 5 Vdc).
b. If you are performing a loop test to verify alarm levels, enter the value representing an
alarm state (see Tables 3-3, 3-4, and 3-5 on page 61).
5. Check that the reference meter displays the commanded output value.
a. If the values match, the transmitter and the loop are configured and functioning
properly.
b. If the values do not match, the meter may be attached to the wrong loop, there may be
a fault in the wiring or power supply, the transmitter may require an output trim, or the
reference meter may be malfunctioning.
After completing the test procedure, the display returns to the Loop Test screen to choose
another output value or to end loop testing.
Traditional 4-20 mA Fast Keys
1, 2, 2
Traditional 1-5 Vdc Fast Keys
1, 2, 2
Device Dashboard Fast Keys
3, 5, 1
- Protocol 1
- Rosemount 3051 Pressure 3
- Transmitter 3
- Title Page 4
- Contents 5
- 3Section 3: Configuration 6
- 5Section 5: Troubleshooting 7
- Reference Manual 10
- Table of Contents 10
- Section 1 Introduction 11
- 1.3 Models covered 12
- 1.4 Transmitter overview 13
- Section 2 Installation 15
- 2.3 General considerations 16
- 2.4 Mechanical considerations 17
- 2.8 Installation procedures 20
- Flange bolts 21
- Bolt installation 23
- 2.8.2 Impulse piping 24
- Mounting requirements 25
- 2.8.3 Process connections 26
- O-rings: 27
- 2.8.5 Housing rotation 28
- 2.8.6 LCD display 29
- Security (write protect) 30
- TRANSMITTER SECURITY 31
- JUMPER POSITIONS 31
- 2.9 Electrical considerations 32
- 2.9.2 Wiring 33
- Section 2: Installation 34
- Installation 34
- Power supply for 4-20 mA HART 35
- 2.9.4 Grounding 37
- Signal wiring 38
- Transmitter case 38
- External Ground 39
- Assembly 39
- Figure 2-24. Manifolds 40
- 2.11.4 Manifold operation 41
- 2.12 Liquid level measurement 44
- 2.12.1 Open vessels 45
- 2.12.2 Closed vessels 45
- Dry leg condition 46
- Wet leg condition 46
- Bubbler system in open vessel 46
- Figure 2-26. Wet leg example 47
- Section 3 Configuration 49
- 3.3 Commissioning 50
- 3.3.2 Wiring diagrams 51
- 3.5 Field communicator 52
- Section 3: Configuration 54
- Configuration 54
- 3.8 Check output 60
- 3.8.1 Process variables 61
- 3.8.2 Sensor temperature 61
- 3.9 Basic setup 62
- 3.9.3 Rerange 63
- Field communicator 65
- AMS device manager 65
- 3.9.4 Damping 67
- 3.10 LCD display 68
- 3.11 Detailed setup 71
- 3.12 Diagnostics and service 72
- 3.13 Advanced functions 74
- 3.13.2 Burst mode 77
- 3.14 Multidrop communication 78
- 4.1 Overview 81
- 4.2 Safety messages 81
- 4.3 Calibration overview 82
- TPE = = 0.117% of span 85
- TPE = = 0.105% of span 86
- 4.4 Analog output trim 87
- AMS Device Manager 89
- 4.5 Sensor trim 91
- 4.5.2 Zero trim 92
- 4.5.3 Sensor trim 93
- Zero effect 95
- Span effect 95
- Operation and maintenance 98
- Section 5 Troubleshooting 99
- 5.2.1 Warnings ( ) 100
- Section 5: Troubleshooting 101
- Troubleshooting 101
- Symptom Corrective actions 101
- 5.3 Diagnostic messages 102
- Operation 103
- Span Fail 104
- Local Dsbld 104
- Write Protect 104
- Message Description 105
- 5.4 Disassembly procedures 107
- 5.4.1 Remove from service 108
- 5.4.2 Remove terminal block 109
- 5.5 Reassembly procedures 110
- 00809-0100-4001, Rev JA 111
- November 2012 111
- A.1.2 Reference accuracy 114
- A.1.3 Total performance 114
- A.1.4 Long term stability 115
- A.1.5 Dynamic performance 115
- A.1.9 Vibration effect 116
- A.1.10 Power supply effect 117
- A.2 Functional specifications 118
- A.2.3 Service 120
- A.2.4 4–20 mA (Output Code A) 120
- fieldbus Parameters 121
- Minimum Load Impedance 123
- Indication 123
- Overpressure Limits 123
- A.2.13 Static Pressure Limit 124
- A.2.14 Burst Pressure Limits 124
- A.2.15 Failure Mode Alarm 124
- A.2.16 Temperature Limits 125
- A.3 Physical specifications 126
- A.3.3 Process-Wetted Parts 127
- A.3.5 Non-Wetted Parts 128
- A.3.6 Shipping Weights 129
- A.4 Dimensional Drawings 130
- 3051C Coplanar Flange 131
- Appendix A: Reference Data 132
- 3051T Dimensional Drawings 135
- Pipe Mounting Panel Mounting 136
- 3051L Dimensional Drawings 137
- A.5 Ordering Information 141
- (3051C with Option Code S1)) 146
- OUNDATION fieldbus Protocol ★ 149
- Axxxx Specials •• •• 165
- A.6 Options 166
- Shipping weights 169
- A.7 Spare parts 174
- OUNDATION or PROFIBUS PA) 177
- Mounting brackets Part number 182
- B.1 Overview 185
- B.2 Safety messages 185
- B.2.1 Warnings 186
- FM Approvals 187
- CSA international 187
- European certifications 188
- Japanese certifications 189
- IECEx certifications 189
- Inmetro certifications 190
- China certifications 191
- B.6 Approval drawings 194
- Product certifications 195
- Index-207 217
- Index-208 218
- Index-209 219
- Index-210 220
Související produkty a manuály pro Měření, testování a kontrola Emerson 3051S
Fitness Quest 1400 manuals
Owner’s manuals and user’s guides for Sports and recreation Fitness Quest 1400.
We providing 1 pdf manuals Fitness Quest 1400 for download free by document types: User Manual
Fitness quest 1400 User Manual (35 pages)
Brand: Fitness-quest | Category: Sports and recreation | Size: 3.59 MB |
Table of contents
CAUTION:
3
NOW COMPLETE
11
CRUSH HAZARD
12
CLEANING
15
Electronics
16
Operating
16
Instructions
16
For Your
16
Treadmill
16
QUICK GUIDE
17
PROGRAMS
20
1200 1400
23
IMPORTANT
24
CLOTHING
26
New Balance
35
More products and manuals for Sports and recreation Fitness Quest
| Models | Document Type |
|---|---|
| 9.5e |
User Manual
Fitness Quest 9.5e User Manual,
26 pages
|
| 284 |
User Manual
Fitness Quest 284 User Manual,
25 pages
|
| NBP01075-2 |
User Manual
Fitness Quest NBP01075-2 User Manual,
26 pages
|
| 482u |
User Manual
Fitness Quest 482u User Manual,
13 pages
|
| 1175e |
User Manual
Fitness Quest 1175e User Manual,
13 pages
|
| 1600 |
User Manual
Fitness Quest 1600 User Manual,
35 pages
|
| 6.5r |
User Manual
Fitness Quest 6.5r User Manual,
15 pages
|
| 5.5e |
User Manual
Fitness Quest 5.5e User Manual,
26 pages
|
| 491pr |
User Manual
Fitness Quest 491pr User Manual,
20 pages
|
| 8.0e |
User Manual
Fitness Quest 8.0e User Manual,
26 pages
|
| 1100HR. |
User Manual
Fitness Quest 1100HR. User Manual,
14 pages
|
| 2100HR |
User Manual
Fitness Quest 2100HR User Manual,
13 pages
|
| 5K 6100 |
User Manual
Fitness Quest 5K 6100 User Manual,
15 pages
|
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce