Emerson Bristol ControlWave LP Manuál s instrukcemi Strana 83
- Strana / 166
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
CI-ControlWaveLP Service / 3-13
Table 3-3 - POST Status Codes (Continued)
Hex Code
Status LEDs
1 2 3 4 5 6
Definition
96 0 1 1 0 1 0 initialization before calling C800h.
97 1 1 1 0 1 0 call ROM BIOS extension at C800h.
98 0 0 0 1 1 0 processing after extension returns.
99 1 0 0 1 1 0 configuring timer data area, printer base addr.
9A 0 1 0 1 1 0 configuring serial port base addrs.
9B 1 1 0 1 1 0 initialization before coprocessor test.
9C 0 0 1 1 1 0 initializing the coprocessor.
9D 1 0 1 1 1 0 processing after coprocessor initialized.
9E 0 1 1 1 1 0 check ext kbd, kbdID, numlock settings.
9F 1 1 1 1 1 0 issue keyboard ID command next.
A0 0 0 0 0 0 1 kbd ID flag reset.
A1 1 0 0 0 0 1 do cache memory test.
A2 0 1 0 0 0 1 display any soft errors.
A3 1 1 0 0 0 1 set keyboard typematic rate.
A4 0 0 1 0 0 1 program memory wait states.
A5 1 0 1 0 0 1 clear screen.
A6 0 1 1 0 0 1 enable parity and NMIs.
A7 1 1 1 0 0 1 initialization before calling E000h.
A8 0 0 0 1 0 1 call ROM BIOS extension at E000h.
A9 1 0 0 1 0 1 processing after extension returns.
B0 0 0 0 0 1 1 display system config. Box.
B1 1 0 0 0 1 1 test low memory exhaustively.
B2 0 1 0 0 1 1 test extended memory exhaustively.
B3 1 1 0 0 1 1 enumerate PCI space.
3.4 WINDIAG DIAGNOSTICS
Bristol’s WINDIAG Software is a diagnostic tool used for testing ControlWaveLP I/O, CPU
memory, communications ports, etc., for proper performance. The ControlWaveLP must be
communicating with a PC equipped with BBI’s WINDIAG program. CPU Board con-
figuration switch SW4-8 must be set to the OFF (Closed) position to enable diagnostics.
Communication between the ControlWaveLP (with/without application loaded) and the
PC can be made via a Local or Network Port with the following restrictions:
• CPU Board Switch SW4-8 must be OFF (closed) to run the WINDIAG program. Setting
SW4-8 OFF will prevent the ‘Boot Project’ from running and will place the unit into
diagnostic mode.
• Any ControlWaveLP communication port can be connected to the PC provided their
port speeds match. Most PCs have a COM1 port (typically RS-232 and defaulted to 9600
bps operation).
• Communication port COM1 is only forced to 9600 bps operation when CPU Switches
SW4-3 and SW4-8 have both been set OFF (closed). COM1 can also be set to 9600 bps
operation via user defined Soft Switches.
• Setting CPU Board Switches SW4-3 and SW4-8 OFF (closed) prevents the ‘Boot Project’
from running, places the unit into diagnostic mode and forces communication ports
COM1 through COM5 to operate at 9600 baud.
COM1: From the factory, COM1 defaults to 115.2 kbd (RS-232) using the Internet Point to
Point Protocol (PPP). Note: ControlWaveLP Port COM1 will be configured for RS-
232 operation (at 9600 baud) by setting CPU Switches SW4-3 and SW4-8 OFF.
- Low Power ControlWave 1
- Telephone (860) 945-2200 2
- WARRANTY 3
- REMEDIES 3
- Training 6
- Help Files / Release Notes 7
- Training Courses 8
- CI-ControlWaveLP 9
- CI-ControlWaveLP 10
- LOW POWER ControlWave 10
- Section 1 13
- INTRODUCTION 13
- 1.3 PHYSICAL DESCRIPTION 16
- MC/PFIN LEDs 33
- 1.4 OPTIONS 34
- Section 2 35
- INSTALLATION 35
- 2.2.2 Vibration Limits 37
- 2.3.4 Communication Ports 44
- 2.4 WIRING NOTES 49
- 2.5 OPERATIONAL DETAILS 59
- Section 3 71
- SERVICE 71
- Caution 72
- 3-4 / Service ControlWaveLP 74
- 3.2 TROUBLESHOOTING TIPS 76
- 3-8 / Service ControlWaveLP 78
- 3.2.3 Wiring/Signal Checks 79
- 3.3 GENERAL NOTES 80
- 3.4 WINDIAG DIAGNOSTICS 83
- Test responses: 88
- 3.5 CORE UPDUMP 90
- Section 4 91
- ~REFRESH N/C 93
- DIS-STATUS-LEDS 93
- 4.2 COMMUNICATION PORTS 94
- BLANK PAGE 102
- PC/104 ANALOG OUTPUT MODULE 103
- Appendix 1 104
- DESCRIPTION 105
- 2 PC-104 AO Module Option 106
- 3 PC-104 AO Module Option 107
- 4 PC-104 AO Module Option 108
- PC/104 AO Board Field Wiring 109
- 6 PC-104 AO Module Option 110
- 7 PC-104 AO Module Option 111
- SPECIFICATIONS 113
- Environmental Specifications 114
- MATERIAL SAFETY DATA SHEET 117
- Page 2 of 4 118
- Page 3 of 4 119
- Page 4 of 4 120
- Supplement Guide - S1400CW 121
- NOTICE 122
- Supplement Guide S1400CW 123
- Section 1 - Overview 125
- Section 2 - Protection 126
- 3.3 EARTH GROUND CONNECTIONS 129
- 4.1 STROKES & STRIKES 139
- 4.1.2 Antenna Caution 141
- 4.1.3 Ground Propagation 143
- 4.1.4 Tying it all Together 143
- 5.1 OVERVIEW 145
- 5.2 INSTRUMENT WIRING 145
- 5.2.5 Earth Ground Wires 147
- READER RESPONSE FORM 151
- Mail this page to: 151
- Bristol Babcock Inc 151
- 1100 Buckingham Street 151
- Watertown, CT 06795 151
- ESDS Manual 153
- TABLE OF CONTENTS 155
- TOOLS AND MATERIALS REQUIRED 155
- ControlWaveLP Low Power PAC 166
Související produkty a manuály pro Sítě Emerson Bristol ControlWave LP
Sítě Emerson FM-3 Specifikace
(110 stránky)
(110 stránky)
Sítě Emerson FM-3 Uživatelský manuál
(8 stránky)
(8 stránky)
Sítě Emerson Liebert ICOM-DO Uživatelský manuál
(12 stránky)
(12 stránky)
Sítě Emerson Liebert CW Uživatelský manuál
(136 stránky)
(136 stránky)
Sítě Emerson Liebert FPC Uživatelský manuál
(58 stránky)
(58 stránky)
Sítě Emerson FM-3 Uživatelská příručka
(263 stránky)
(263 stránky)
Sítě Emerson MONITORING OpenComms Uživatelský manuál
(88 stránky)
(88 stránky)
(88 stránky)
Sítě Emerson Liebert Xtreme Density Specifikace
(104 stránky)
(104 stránky)
Sítě Emerson Mynah PLC-5 Datový list
(18 stránky)
(18 stránky)
Sítě Emerson X-web500 Instalační příručka
(23 stránky)
(23 stránky)
Sítě Emerson X-web500 Uživatelský manuál
(116 stránky)
(116 stránky)
Sítě Emerson Mynah SLC-500 Uživatelská příručka
(131 stránky)
(131 stránky)
Sítě Emerson X-web300 Uživatelský manuál
(26 stránky)
(26 stránky)
Sítě Emerson MONITORING OpenComms Uživatelský manuál
(48 stránky)
(48 stránky)
Vivitek Projectors user manuals
Starting on H
Komentáře k této Příručce