Emerson MICRO MOTION 2700 Instalační manuál Strana 126
- Strana / 264
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
116 Transmitter Configuration and Use: Series 1000 and 2000 Transmitters
Troubleshooting continued
10.10 Transmitter status LED
10.10.1 Model 1500/2500 transmitters
The Model 1500/2500 transmitter includes a LED that indicates transmitter status. See Table 10-3.
If the status LED indicates an alarm condition:
1. View the alarm code using ProLink II or a Communicator.
2. Identify the alarm (see Section 10.11).
3. Correct the condition.
10.10.2 Model 1700/2700 transmitters with displays
The display on the Model 1700/2700 transmitter includes a LED that indicates transmitter status. See
Table 10-4.
If the status LED indicates an alarm condition:
1. View the alarm code using the procedures described in Section 7.6.
2. Identify the alarm (see Section 10.11).
3. Correct the condition.
4. If required, acknowledge the alarm using the procedures described in Section 7.7.
FO phase on Channel C
does not change with flow
direction (Config IO
transmitters only)
Wrong configuration setting FO mode must be set to Quadrature for phase to
automatically track flow direction.
DI is fixed and does not
respond to input switch
(Config IO transmitters only)
Possible internal/external power
configuration error
Internal means that the Configurable I/O will
supply power. External means that an external
pull-up resistor and source are required. Verify
configuration setting is correct for desired
application.
Cannot configure Channel B
for DO1 operation (Config IO
transmitters only)
Channel C is configured as FO FO and DO1 use the same circuitry and cannot
run simultaneously. Configure Channel B as FO
and Channel C as DO2.
Cannot configure Channel C
for FO operation (Config IO
transmitters only)
Channel B is configured as DO1 FO and DO1 use the same circuitry and cannot
run simultaneously. Configure Channel B as FO
and Channel C as DO2.
Table 10-3 Model 1500/2500 transmitter status reported by the status LED
Status LED state Alarm priority Definition
Green No alarm Normal operating mode
Flashing yellow No alarm Zero in progress
Yellow Low severity alarm • Alarm condition: will not cause measurement error
• Outputs continue to report process data
Red High severity alarm • Alarm condition: will cause measurement error
• Outputs go to configured fault indicators
Table 10-2 Milliamp and frequency output problems and remedies (continued)
Symptom Possible cause Possible remedy
- Micro Motion 1
- Series 1000 and 1
- Series 2000 Transmitters 1
- Contents 5
- Chapter 1 11
- Before You Begin 11
- Before You Begin continued 13
- Topic Document 13
- Term Definition 13
- Item Configuration data 15
- Chapter 2 17
- Using the Transmitter Display 17
- –8.100E 5 19
- Chapter 3 21
- Poll button in the Connect 26
- 1 and 2, or to the 26
- Connect to Device 32
- Chapter 4 33
- 375 Field Communicator 33
- Chapter 5 39
- Flowmeter Startup 39
- Flowmeter Startup continued 40
- 5.5.3 Zeroing with ProLink II 50
- Chapter 6 53
- Sensor type 54
- T- S er ie s O t he r 54
- Newer tag Older tag 55
- Flow FCF X.XXXX FT X.XX 56
- Terminals 58
- Default Process 58
- Mass flow unit 60
- Volume flow unit 61
- ProLink II code 69
- Communicator 69
- Polarity 75
- Output power 75
- Description 75
- Assignment ProLink II code 77
- Using the Transmitter 79
- Chapter 7 79
- • Model 1700 AN 84
- • Model 1700 IS 84
- • Model 2700 AN 84
- • Model 2700 IS 84
- • Model 2700 CIO 84
- Scroll optical switch 85
- Select optical switch 85
- Function name Communicator 86
- ProLink II 86
- ProLink 87
- Totalizer Control 87
- With a Communicator 88
- Chapter 8 89
- Optional Configuration 89
- Table 8-1 Configuration map 90
- Special 92
- • Model 2500 CIO 93
- Variable Description 94
- Cutoff type Default Comments 96
- Example 1 100
- Example 2 100
- Example 3 101
- Informational panel of the 102
- Status window 102
- Scroll to view process 104
- Max Int. Totalizers stop 106
- Parameter 109
- Series 1000 Series 2000 110
- Process variable 110
- PV SV TV QV PV SV TV QV 110
- Parameter Description 111
- Chapter 9 113
- Compensation, and Polling 113
- Pressure unit 114
- Static pressure 116
- Polled Var 1 119
- Chapter 10 121
- Troubleshooting 121
- Troubleshooting continued 122
- Section Topic 122
- Symptom Cause Possible remedy 132
- Pickoff value 141
- Cause Possible remedy 141
- Test terminal pair 146
- Colors Numbers 146
- Possible cause Solution 147
- Appendix A 151
- Default Values and Ranges 151
- Appendix B 155
- Appendix C 167
- Calibrating the Transmitter 167
- Appendix D 175
- Name Description 176
- Available process variables 178
- Slope and offset 181
- Appendix E 183
- Other configuration options 185
- Preferences menu 187
- Figure E-4 Communicator menus 188
- Appendix F 193
- Figure F-4 Communicator menus 197
- Appendix G 203
- Transmitters 203
- Figure G-4 Communicator menus 207
- Enter password if required 212
- Appendix H 219
- Figure H-4 Communicator menus 223
- Appendix I 235
- Configuration 237
- Figure I-4 Communicator menus 239
- On-Line Menu 240
- 3 Basic Setup 240
- 4 Detailed Setup 240
- 5 Review 243
- Appendix J 251
- Select to disable 252
- Select to enable 252
- Index continued 256
- *20001715* 264
Související produkty a manuály pro Měření, testování a kontrola Emerson MICRO MOTION 2700
(3 stránky)
Měření, testování a kontrola Emerson 3051S Specifikace
(188 stránky)
(188 stránky)
Měření, testování a kontrola Emerson 3051S Specifikace
(240 stránky)
(240 stránky)
Měření, testování a kontrola Emerson 3051S Specifikace
(240 stránky)
(240 stránky)
Měření, testování a kontrola Emerson 644 Specifikace
(182 stránky)
(182 stránky)
Měření, testování a kontrola Emerson 3051S Specifikace
(222 stránky)
(222 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.132 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce